 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TACT SwitchTM Low-profile with High Operation Force (Snap-in Type) SKPE Series High operation force best suitable for automotive use. Detector Push Slide Rotary Encoders Power Dual-in-line Package Type TACT SwitchTM www..com Product Line CustomProducts Product No. SKPEADA010 SKPEAAA010 SKPEABA010 Operating Operating direction force 1.18N 2.45N 2.94N Vertical 1.3 5mA 12V DC 10BA 1V DC 50,000cycles 1k max. Travel mm Rating max. Rating min. Operating life 5mA 5V DC Initial contact resistance Rubber color Light blue Green Blue Minimum order unit pcs. 1,000 Dimensions Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type 0.2 6.3 6.6 2.5 Unit:mm Style PC board mounting hole dimensions Viewed from switch mounting face 6.5 Rubber dome 2-o1.3 holes 3.3 1 6.5 2 3.5 5 1 5.8 Circuit Diagram 1 2 Note Using a 1.6mm thick PC board is recommended. Refer to P.306 for soldering conditions. 298 TACT SwitchTM www..com List of Varieties Soft Feeling Type Series SKEG SKPE SKEG SKEY SKPF SKPM SKPN SKPG SKPL SKPD Detector Push Type Features Operating direction Electrical performance Durability Environmental performance Vertical Encoders Horizontal Power W Dimensions mm 6 6.6 6.3 7 5 7.5 7.8 9.9 7.3 Carbon 5 9 10 6 5 Silver 6.7 7 Carbon 6.3 5 Silver Carbon 8 5.9 6 6.6 V6.45 7.8 Snap-in Horizontal type High operation force and long stroke Surface mount Low contact resistance Radial Round terminal and low contact resistance Photo Slide Rotary D H Dual-in-line Package Type TACT SwitchTM Contact 1N Operation force coverage 5N Ground terminal Operating temperature range Insulation resistance Voltage proof Vibration Lifetime Cold Dry heat Damp heat Page 296 298 CustomProducts 20 to 40 70 to SKEG 90 Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type 100M min. 100V DC SKEY/PD 50M min. 100V DC 250V AC for 1min. SKPN : 200V AC for 1min. SKEY/PD : 100V AC for 1min. 10 to 55 to 10Hz/min., the amplitude is 1.5mm for all the frequencies, in the 3 direction of X, Y and Z for 2hours respectively Shall be in accordance with individual specifications. 30 80 60 296 299 2 2 2 for 96h for 96h , 90 to 95%RH for 96h 300 301 302 303 304 305 W Width. The most outer dimension excluding terminal portion. D Depth. The most outer dimension excluding terminal portion. H Height. The minimum dimension if there are variances. 251 TACT SwitchTM www..com Soldering Conditions Condition for Reflow Available for Surface Mount Type. 1. Heating method: Double heating method with infrared heater. 2. Temperature measurement: Thermocouple 0.1 to 0.2 Detector Push Slide Rotary Encoders Power CA K or CC T at solder joints copper foil surface . A heat resistive tape should be used to fix thermocouple. 3. Temperature profile Temperature (C ) 260C max. 3 sec max. 180 150 Time 230C Dual-in-line Package Type TACT SwitchTM 40s max. 3 to 4min. CustomProducts Time inside soldering equipment Note 1. The above temperature shall be measured on the mounting surface of a PC board. There are cases where the PC board's temperature greatly differs from that of the switch, depending on the material, size, thickness of PC boards and others. The above-stated conditions shall also apply to switch surface temperatures. 2. Soldering conditions differ depending on reflow soldering machines. Prior verification of soldering condition is highly recommended. Sharp Feeling Soft Feeling Snap-in Type Surface Mount Type Radial Type Conditions for Auto-dip Available for Snap-in Type and Radial Type Except SKHJ, SKHL, SKQJ, SKQK, SKEG series Items Flux built-up Condition Mounting surface should not be exposed to fluk Ambient temperature of the soldered surface of PC board. 100 max. 60s max. 260 max. Manual Soldering Except SKRT Series Items Soldering temperature Duration of soldering Capacity of soldering iron Condition 350 max. 3s max. 60W max. Preheating temperature Preheating time Soldering temperature Duration of immersion Number of soldering 5s max. 2times max. Notes 1. 2. 3. 4. 5. Consult with us for availability of TACT SwitchTM washing. Prevent flux penetration from the top side of the TACT SwitchTM. Switch terminals and a PC board should not be coated with flux prior to soldering. The second soldering should be done after the switch is stable with normal temperature. Use the flux with a specific gravity of min 0.81. EC-19S-8 by TAMURA Corporation, or equivalents. 306 |
Price & Availability of SKPE
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |